Hi, I’m Eldad Sameach from Dr. Fix it yourself In this video clip I want to show you how to Fix a gas flame nozzle. The flames are so optimal, If we take a look at this flame, It works relatively OK, This flame is OK, and also that one, But that flame is very poor, and the gas hardly flows out. OK, we got the picture, so we can turn the flames off. I’ll show you how to open each one of the flames, And inside it there’s a nozzle, We’ll take it out, clean it, and the flame will be as good as new. So, let’s get to work. OK, We waited for the flames to cool, before attending to them, So we won’t get our fingers burnt. And we lifted up the 2 parts and put them aside. There’s the iron cast part, and the aluminum part. It’s important to keep each flame with its original parts, because it’s sized. Now let’s take a look at the nozzle. We have 4 nozzles… The nozzle is what we see here… It’s something small with a tiny hole, from which the gas comes out, And mixed with air, we get a flame. We need to remove all 4 nozzles, And to clean them with oil remover, We’ll use a key wrench cap to open the nozzle, Just put on the nozzle and unscrew it. Turn counter clock wise, gently. We can use tweezers to remove the nozzle. This is the nozzle, There’s a screw thread on one side, And hexagonal head With a tiny hole in its center, which lets the gas out. Oil and dirt clog it over time. We’ll take out all the nozzles, Immerse them in oil remover substance, Or any other substance that will remove the oil and dirt, And after some time, we’ll rinse it, dry it and reinstall them. That’s all. Something important: We need to make sure to install each nozzle in its original flame! Otherwise, we’ll a small flame in place of a big one, and vice versa. To avoid any confusion, we’ll put each nozzle aside its flame. We’ll remove all 4 nozzles first. This is the nozzle, we took a plastic cup and cut it in half, We’ll spray on it an oil remover liquid. The nozzle is immersed in the liquid. Now we put it aside to rest and absorb the liquid. And… We’ll do that with all 4 nozzles, and let them rest and absorb the liquid for about 30 minutes. After immersion, this is how it looks like… Each nozzle is in a plastic cup, Near its flame, We can touch the oil remover liquid with bare hands, See the black substance that in the plastic cup… This is the removed oil And we’ll add to it By taking a very thin pin And penetrate it into the tiny hole, Trying to take out more dirt, This may help… To clean the oil in addition to the oil remover liquid. We’ll do that for all 4 nozzles. And then we’ll rinse them, and reinstall them. We took advantage of the situation and cleaned all the oil stains from the gas top. this is how the nozzle looks… It’s the biggest flame’s nozzle… Maybe you can notice the hole… Obviously, the bigger the flame, the bigger the nozzle, although it’s hard to tell by sight. We’ll take the nozzle, And screw it back in place, It requires gentleness and patience. With the key wrench tool. Tighten it relatively loosely, Use very little force. Do that with all nozzles. We put back the aluminum and iron cast parts for all flames. Let’s see how it looks… The biggest flame was OK, it’s a bit bigger now, This flame was poor, almost gone, and now it’s very rich. This flame was also poor and now it’s very intense, And also the flame here was poor, half power. Now all the flames are in full power, for few minute work,. Plus 30 minutes waiting for the oil remover to do its job. Amazing! I’m Eldad Sameach from Dr. Fix it yourself. In this video clip I showed you how to renew The gas flames, by cleaning the nozzles that let the gas flow. Visit my web site, See more free videos and posts that will assist you in fixing all kinds of things. Use them, share them, fix by yourself, And I’ll see you in my next videos.